Published: January 16, 2027 | Last updated: January 16, 2027
TL;DR
- Loctite C5-A is a copper and graphite anti-seize paste that protects metal parts from rust, corrosion, galling and seizing (Boeing Distribution, 2026).
- It works from -29 to 982°C, or about -20 to 1,800°F (Ellsworth, 2026).
- It suits threads, bolts, studs and flanges on many metals, including steel, stainless steel and cast iron (TEquipment, 2026).
- Never put anti-seize on brake slide pins, pad friction surfaces or rotor braking surfaces.
- Most vehicle makers specify clean, dry wheel studs; anti-seize changes torque readings, so follow your service manual.
Disclosure: As an Amazon Associate, Brakes Hub earns from qualifying purchases. This never changes our verdicts.
How we reviewed this product: we studied Loctite's published specifications through distributor listings and general brake service practice. We did not run our own tests.
What Is Loctite C5-A Copper Anti-Seize?
Loctite C5-A is a paste that stops metal parts from rusting or seizing together. Henkel's formula suspends copper and graphite in a high-quality grease (Boeing Distribution, 2026).
It is also called Loctite LB 8008 C5-A. It comes in brush-top cans, tubes, aerosols and large pails.
Typical uses include fasteners, pipe fittings and high-temperature assemblies such as exhaust systems (TestEquity, 2026).
How Anti-Seize Works
Anti-seize fills the tiny gaps between mating metal surfaces. The copper and graphite particles keep the surfaces apart so rust and heat cannot weld them together (TestEquity, 2026).
That makes bolts and parts much easier to remove later, even after years of heat and road salt.
A good comparison is baking paper in a hot oven. It stops food from sticking to the tray, so it lifts off cleanly.
Loctite C5-A Specifications at a Glance
| Specification | Loctite C5-A |
|---|---|
| Base | Copper and graphite in grease |
| Temperature range | -29 to 982°C (about -20 to 1,800°F) |
| Form | Paste or aerosol |
| K-value | 0.16 |
| Electrically conductive | Yes |
| Metals | Copper, brass, cast iron, steel, stainless steel and alloys |
Sources: Ellsworth (2026); TEquipment (2026); Mars Supply (2026).
Where to Use Copper Anti-Seize on a Brake Job
On a brake job, a thin film of anti-seize helps on rusty mating surfaces that must come apart later, as long as it stays away from rubber and friction surfaces.
- A very thin film on the hub face can help stop the rotor rusting to the hub. Wipe off any excess.
- Caliper bracket bolts, if your service manual allows a lubricant on them.
- Exhaust and other high-heat bolts near the brakes.
Before fitting new rotors, clean the hub first with a tool such as the Powerbuilt hub resurfacing kit.
Where Not to Use Anti-Seize
Anti-seize must never touch rubber parts or friction surfaces. Use the right product for each job.
| Place | Use anti-seize? | Use instead |
|---|---|---|
| Caliper slide pins | No | Synthetic brake grease such as Sil-Glyde |
| Pad backing plate contact points | Not recommended | Ceramic brake grease such as Permatex Ceramic Extreme |
| Pad friction surface or rotor face | Never | Nothing; keep them clean |
| Wheel studs | Usually no | Clean, dry threads unless your manual says otherwise |
Lubricated threads tighten further for the same torque reading. With a K-value of 0.16, C5-A changes the torque-to-clamp relationship, so wheel nuts torqued on lubricated studs can end up over-tightened (Mars Supply, 2026).
How to Apply Loctite C5-A
To apply C5-A, clean the parts, brush on a thin, even coat, assemble, and wipe off any excess. Follow these steps.
- Clean threads and surfaces with a wire brush and brake cleaner.
- Let the parts dry completely.
- Brush a thin coat onto the male threads or mating surface.
- Assemble and tighten to the manual's specification.
- Wipe away any excess, especially near brake pads and rotors.
Pros and Cons of Loctite C5-A
The main strength of Loctite C5-A is strong protection against seizing in very high heat, and the main limit is that it suits only certain places on a brake job.
Pros
- Works up to 982°C.
- Protects against rust, corrosion and galling.
- Makes later disassembly much easier.
- Works on a wide range of metals.
Cons
- Not for slide pins, rubber parts or friction surfaces.
- Changes torque readings on threaded fasteners.
- Can be messy if over-applied.
How Much Anti-Seize to Use
Use a thin, even film. More anti-seize does not give more protection, and extra paste can spread onto brake parts that must stay clean.
- Coat only the male threads or the mating face, not the whole part.
- Use the brush-top can for small parts, so you can control the amount.
- Wipe any excess off with a clean rag before you fit the wheel.
- Keep the can closed between uses so dirt does not get into the paste.
Choosing the Right Type of Anti-Seize
Loctite and other makers sell several types of anti-seize, such as copper, nickel and metal-free grades, each suited to different metals and temperatures. C5-A is a general-purpose copper grade for very high heat (TestEquity, 2026). For special metals or sensitive parts, read the product label and your service manual, and choose the grade they recommend.
Whatever type you use, the same brake rule applies: keep anti-seize away from pads, rotor faces, slide pins and rubber boots.
Frequently Asked Questions About Loctite C5-A
What temperature can Loctite C5-A handle?
From -29 to 982°C (Ellsworth, 2026).
Can I use copper anti-seize on brake slide pins?
No. Use a synthetic brake grease made for rubber boots.
Should I put anti-seize on wheel studs?
Most vehicle makers specify clean, dry studs. Lubricant changes torque readings, so follow your service manual.
Can I put anti-seize on the hub face?
A very thin film can help stop the rotor rusting to the hub. Wipe off any excess.
What metals does Loctite C5-A work on?
Copper, brass, cast iron, steel, stainless steel and other alloys (TEquipment, 2026).
Is Loctite C5-A electrically conductive?
Yes, it is listed as electrically conductive (Mars Supply, 2026).
Summary: Is Loctite C5-A Worth Buying?
- Loctite C5-A protects metal parts from seizing up to 982°C.
- Use a thin film on hub faces and high-heat bolts.
- Never use it on slide pins or friction surfaces.
- Follow your manual for wheel studs, usually clean and dry.
Check Loctite C5-A on Amazon →
Safety note: brakes are safety parts. If you are not sure how to do the job, have a qualified mechanic do it.