Published: December 31, 2026 | Last updated: December 31, 2026
TL;DR
- The Powerbuilt resurfacing kit (940382) removes rust and grime from wheel hubs, rotors and lug studs using a power drill (Powerbuilt, 2026).
- The kit includes a drill attachment, 3 hook-and-loop pad holders and 10 heavy-duty abrasive pads (Powerbuilt, 2026).
- The attachment fits any corded or cordless drill chuck (Powerbuilt, 2026).
- Rust between the hub and rotor is the most common cause of rotor runout and a pulsing brake pedal (Phoenix Systems, 2026).
- Owners say it cleans around the base of each stud so new rotors sit flatter and run truer (eBay, 2026).
Disclosure: As an Amazon Associate, Brakes Hub earns from qualifying purchases. This never changes our verdicts.
How we reviewed this product: we studied Powerbuilt's product information, retailer listings, owner feedback and published brake service guidance. We did not run our own tests.
What Is the Powerbuilt Hub Resurfacing Kit?
The Powerbuilt Brake Rotor, Wheel Hub and Lug Stud Resurfacing Kit is a drill-powered tool for cleaning rust off the hub face before you fit a rotor. Powerbuilt says it works on most vehicles with front or rear disc brakes (Powerbuilt, 2026).
The attachment has a hole in the center, so it slides over each lug stud and cleans the ring of hub surface around it.
Powerbuilt is a hand tool brand known for automotive specialty tools.
Why Hub Rust Causes Brake Problems
Rust on the hub face stops the rotor from sitting perfectly flat. Even a thin layer can tilt the rotor slightly, which creates runout.
Rotor runout makes the pads touch the rotor's high spots on every turn. Over a few thousand miles, this wears the rotor unevenly and causes a pulsing pedal. Phoenix Systems names hub rust as the number one cause of runout (Phoenix Systems, 2026).
A good comparison is a table with a coin under one leg. Everything on it wobbles until you clear what is underneath.
Powerbuilt Hub Resurfacing Kit at a Glance
| Detail | Powerbuilt 940382 |
|---|---|
| Power source | Corded or cordless drill |
| Contents | Drill attachment, 3 pad holders, 10 abrasive pads |
| Pad attachment | Hook-and-loop for quick changes |
| Cleans | Wheel hubs, rotors and lug studs |
| Fit | Most vehicles with front or rear disc brakes |
Source: Powerbuilt (2026).
How to Clean a Wheel Hub With the Powerbuilt Kit
To clean a hub, remove the rotor, fit a pad to the attachment, slide it over each stud in turn and run the drill until the hub face is clean metal. Follow these steps.
- Lift the car, support it on jack stands and remove the wheel, caliper, bracket and rotor.
- Wear safety glasses and gloves, because rust particles fly off.
- Fit an abrasive pad to the holder and lock the attachment into your drill.
- Slide the attachment over a lug stud and press it lightly against the hub face.
- Run the drill at a moderate speed until the ring around the stud is clean, bright metal.
- Repeat at each stud, then clean any remaining rust with a wire brush.
- Blow or wipe off all dust, and wipe the hub with brake cleaner.
Fit the new rotor, torque the wheel nuts and check runout with a dial indicator.
Should You Put Anti-Seize on the Hub?
A very thin film of anti-seize on the hub face can help stop the rotor rusting to the hub next time. Keep it thin and keep it off the wheel studs' threads unless your service manual allows it.
Too much anti-seize can itself create a layer that affects how flat the rotor sits. Wipe off any excess.
Never put anti-seize or grease on the rotor braking surface.
Other Ways to Clean a Hub
| Method | Speed | Best for |
|---|---|---|
| Drill-powered resurfacing pads | Fast | Clean, even results around each stud |
| Wire brush by hand | Slow | Light rust only |
| Wire wheel on a drill | Fast | Heavy rust, but harder around studs |
| Sandpaper by hand | Slow | Small areas |
For rotors that stay cleaner, consider coated rotors such as Wagner E-Shield.
Pros and Cons of the Powerbuilt Hub Resurfacing Kit
The main strength of the Powerbuilt kit is fast, even hub cleaning around each stud with any drill, and the main limit is that the pads wear and need replacing.
Pros
- It works with any corded or cordless drill.
- The center hole cleans neatly around each stud.
- Hook-and-loop pads change quickly.
- Owners report rotors run truer after cleaning (eBay, 2026).
Cons
- Abrasive pads wear out and need replacing.
- It creates rust dust, so eye protection is needed.
- It cannot reach rust in deep corners of some hubs.
Common Problems After Fitting New Rotors
| Problem | Likely cause | Solution |
|---|---|---|
| Pulsing pedal soon after the job | Rust left on the hub | Clean the hub fully and check runout |
| Steering shake at speed | Uneven wheel nut torque | Torque nuts in a star pattern |
| Rotor will not sit flat | Rust ridge around studs | Clean around each stud base |
| Runout still high after cleaning | Bent hub or worn bearing | Check the hub flange and bearing |
Frequently Asked Questions About the Powerbuilt Hub Resurfacing Kit
What comes in the Powerbuilt hub resurfacing kit?
A drill attachment, 3 hook-and-loop pad holders and 10 abrasive sanding pads (Powerbuilt, 2026).
Does the Powerbuilt kit fit my drill?
Powerbuilt says the attachment fits any brand of corded or cordless drill chuck (Powerbuilt, 2026).
Why should I clean the wheel hub?
Hub rust is the most common cause of rotor runout, which leads to a pulsing pedal (Phoenix Systems, 2026).
Can I use it on lug studs?
Yes. Powerbuilt lists brake rotors, wheel hubs and lug studs (Powerbuilt, 2026).
Does it work on rear disc brakes?
Yes. It works on most vehicles with front or rear disc brakes (Powerbuilt, 2026).
Should I check runout after cleaning the hub?
Yes. A runout check confirms the new rotor sits true.
Summary: Is the Powerbuilt Hub Resurfacing Kit Worth Buying?
- The Powerbuilt kit cleans rust from hubs, rotors and lug studs with any drill.
- Clean hubs help new rotors sit flat and run true.
- Wear eye protection and clean off all dust afterward.
- Check runout after fitting the new rotor.
See also our rotor micrometer guide and our DIY brake job tools checklist.
Check the Powerbuilt hub resurfacing kit on Amazon →
Safety note: brakes are safety parts. If you are not sure how to do the job, have a qualified mechanic do it.