How to change your Genesis Coupe’s brakes from Brembo to OEM
If you own a Genesis Coupe with Brembo brakes and want to change them to OEM brakes, this guide will show you how.
In it, we'll show you how to switch your car's brakes from Brembo to the OEM setup. It's not as hard as it sounds, and best of all, it'll save you a few bucks. So read on, and learn how to do it yourself.
Anybody can perform this task with a few tools. You'll need a jack, a wrench, and a socket set. With these tools and a little bit of know-how, you can have your Genesis Coupe's brakes swapped out in no time.
How to change your Genesis Coupe's brakes from Brembo to OEM
If your Genesis Coupe is equipped with Brembo brakes and you want to change to OEM brakes, there are a few things you need to do. First, you'll need to purchase the OEM brake kit, which includes the calipers, rotors, and pads. Follow these steps once you have the kit:
- Jack up your car and remove the wheels
- Remove the calipers from the rotor by unbolting them
- Install the new calipers in the same position and bolt them in place
- Attach the new rotors to the calipers and hand-tighten the bolts.
- Insert the new pads into the calipers and compress them, so they fit snugly against the rotors
- Reinstall your wheels and lower your car off the jack stands
- Lower your car back down onto the ground and drive away
The next step is to bleed the brakes. To do this, you'll need to use a unique tool called an air compressor. The tool has a hose attached to it that goes directly into the master cylinder. First, open the hood and locate the master cylinder on the driver's side of the engine compartment.
Using the air compressor, blow air through the hose until the pressure gauge reads 0 psi. Then close the hood and let the system run for about 10 minutes.
After 10 minutes, recheck the pressure and make sure it's still at 0 psi. If it isn't, repeat the previous step. Once the brakes have been bled, you should be good to go. Your new OEM brakes should perform better than the original ones did.
HOW TO CHANGE YOUR GENESIS COUPE'S BRAKES FROM BREMBO TO OEM FAQS:
What is the cost of changing the brakes on a Genesis Coupe?
The cost of changing the brakes on a Genesis Coupe will vary depending on the type of brakes you have. For example, if you have disc brakes, you'll need to replace both the pads and the rotors for toyota tacoma or other vheicles.
This can cost anywhere from $200 to $400. However, if you have adjustable drum brakes, you'll only need to replace the pads, which will cost around $100. In addition to the cost of parts, you'll also need to factor in labor costs.
Can I replace the rotors instead of changing the entire wheel assembly?
Yes, but you'll also need to get a different wheel style. Most people don't realize that the rotors come in two types: cast iron or forged aluminum. Cast iron rotors are cheaper but won't last as long because they aren't heat-treated like forged aluminum rotors.
Will I lose any performance if I change my brakes?
No, not really. Many people prefer the look of forged aluminum rotors over cast iron rotors. They also tend to hold their value longer than cast iron rotors, which makes sense since they're made from higher-quality materials.
What are the benefits of changing to OEM brakes?
Regarding your brakes, you want to ensure you have the best possible product for your vehicle. There is no doubt that your brakes are what keep you safe on the road, so, what are the benefits of changing to OEM brakes?
One benefit of changing to OEM brakes is that you can be sure you’re getting a high-quality product. OEM brakes are made to meet the specific standards of your vehicle, so you know they’ll work well.
Another benefit of switching to OEM brakes is that they can help improve your gas mileage. Because they’re designed specifically for your car, they work more efficiently than aftermarket brakes. This means your vehicle doesn’t have to work as hard, saving you money at the pump.
What are the required tools and steps for this process?
You'll need a jack, a socket set, a wrench, and an air compressor (or a similar tool) to complete this job.
Final Verdict
Changing your Genesis Coupe's brakes from Brembo to OEM is a pretty straightforward process. The process should only take you an hour or so, and you'll need a few essential tools.
However, once you're finished, you'll have a much better understanding of how your brakes work and feel, and you'll be able to enjoy the peace of mind that comes with knowing you did the job yourself.
