Published: December 25, 2026 | Last updated: December 25, 2026
TL;DR
- The Lisle 23000 is a locking hose pincher that clamps flexible rubber hoses up to 3/4-inch inside diameter (Lisle, 2026).
- Angled, offset jaws close to create a complete seal and reach tight spaces (Lisle, 2026).
- The handles lock the jaws closed, so both of your hands are free for the job (Lisle, 2026).
- It is made from glass-filled nylon and weighs about 6 oz (Global Test Supply, 2026).
- On brakes, clamp only rubber flex hoses, never braided stainless lines or metal hard lines, and inspect the hose after use.
Disclosure: As an Amazon Associate, Brakes Hub earns from qualifying purchases. This never changes our verdicts.
How we reviewed this product: we studied Lisle's product description, retailer listings and general shop practice for brake hose clamping. We did not run our own tests.
What Is the Lisle 23000 Hose Pincher?
The Lisle 23000 is a plier-style tool that squeezes a flexible hose shut to stop fluid flow. Lisle lists it for brake hoses, vacuum hoses, heater hoses and all flexible rubber hose (Lisle, 2026).
On a brake job, it lets you disconnect a caliper or wheel cylinder without draining the whole system. That saves fluid and helps keep air out of the master cylinder.
Lisle is a US tool maker founded in 1903 in Clarinda, Iowa (ToolsID, 2026).
How the Lisle 23000 Works
The tool works like a pair of locking pliers made for hoses. You squeeze the handles until the angled jaws close fully on the hose, and a ratchet locks them in place (Lisle, 2026).
The jaws are offset so you can reach hoses tucked behind suspension parts or close to the frame.
A good comparison is a clip on a bag of chips. It holds the opening shut so nothing spills while you set the bag down.
Lisle 23000 Details at a Glance
| Detail | Lisle 23000 |
|---|---|
| Hose size | Up to 3/4 inch (19 mm) inside diameter |
| Jaws | Angled and offset |
| Locking | Handles lock the jaws closed |
| Material | Glass-filled nylon |
| Weight | About 6 oz (170 g) |
| Uses | Brake, vacuum, heater and other flexible rubber hoses |
Sources: Lisle (2026); Global Test Supply (2026).
When to Use a Hose Pincher on a Brake Job
A hose pincher is most useful when you disconnect a hydraulic part at one wheel and want to limit fluid loss. Common jobs include:
- Replacing a brake caliper, such as a Cardone remanufactured caliper.
- Replacing a rear wheel cylinder on drum brakes.
- Replacing a caliper's banjo bolt or copper washers.
- Rebuilding a caliper while the hose stays connected to the car.
Even with the hose clamped, you must still bleed that wheel after the job.
How to Use the Lisle 23000 Safely on a Brake Hose
To use the pincher safely, clamp only the rubber part of the brake hose, close it just enough to stop flow, and release it slowly when done. Follow these steps.
- Lift the car, support it on jack stands and remove the wheel.
- Find the rubber section of the brake hose between the frame and the caliper.
- Place the jaws across the middle of the rubber section, away from the metal crimped ends.
- Squeeze until the jaws close and lock. Do not force it past the lock.
- Disconnect and replace the part. Catch any drips with a pan.
- Reconnect the hose, then unlock and remove the pincher slowly.
- Bleed the brake at that wheel. Speed Bleeders make this a one-person job.
Which Brake Hoses You Should Not Clamp
Never clamp braided stainless lines, metal hard lines or old, cracked rubber hoses. Clamping these can damage them and lead to leaks.
- Braided stainless lines, such as Goodridge G-Stop, have a PTFE core that can be damaged by pinching.
- Metal hard lines can crush or kink and must never be clamped.
- Old hoses with visible cracks or swelling should be replaced, not clamped.
After clamping any rubber brake hose, check it for marks, bulges or cracks. Replace it if you see any damage.
Pros and Cons of the Lisle 23000
The main strength of the Lisle 23000 is hands-free hose clamping with a complete seal, and the main limit is that it only suits flexible rubber hoses.
Pros
- Locking handles free both hands.
- Angled, offset jaws reach tight spaces.
- Glass-filled nylon is light and strong.
- One tool works on brake, vacuum and heater hoses.
Cons
- It is not for braided or metal lines.
- Hoses larger than 3/4 inch need a bigger tool.
- Old rubber hoses can be damaged if clamped too hard.
Common Mistakes With Hose Pinchers
| Mistake | Risk | Better approach |
|---|---|---|
| Clamping near the metal crimp | Hose damage at the joint | Clamp the middle of the rubber section |
| Clamping a braided line | Damaged inner liner | Plug the line or cap the fitting instead |
| Skipping the bleed after the job | Air in the system, soft pedal | Bleed the wheel you worked on |
| Leaving it on a cracked hose | Hose splits | Replace the hose |
Frequently Asked Questions About the Lisle 23000
What size hoses does the Lisle 23000 fit?
It clamps flexible hoses up to 3/4-inch inside diameter (Lisle, 2026).
Can I use the Lisle 23000 on brake hoses?
Yes, on flexible rubber brake hoses. Lisle lists brake hoses as a use (Lisle, 2026).
Can I clamp a stainless braided brake line?
No. Clamping can damage the inner liner. Cap or plug the fitting instead.
Do I still need to bleed the brakes after clamping the hose?
Yes. Some air usually enters when the part is disconnected, so bleed that wheel.
What is the Lisle 23000 made from?
It is made from glass-filled nylon for extra strength (Lisle, 2026).
Can I use it on coolant hoses?
Yes. Lisle lists heater and vacuum hoses as well as brake hoses (Lisle, 2026).
Summary: Is the Lisle 23000 Worth Buying?
- The Lisle 23000 clamps flexible hoses up to 3/4 inch with a locking, complete seal.
- It limits brake fluid loss when replacing calipers or wheel cylinders.
- Clamp only rubber flex hoses, never braided or metal lines.
- Always bleed the brakes and inspect the hose afterward.
Check the Lisle 23000 on Amazon →
Safety note: brakes are safety parts. If you are not sure how to do the job, have a qualified mechanic do it.